How to Use Drill Bits? Best User Guide


Narrow diameter cobalt, HSS, or titanium best drill bits are quickly broken, even by pros, so a bit of care needs to take while using them.

Some tips:

When they snag/catch in the workpiece, small bits frequently break. So if you have a cordless drill, utilize that in place of a central corded drill. When the bit snags, the chuck will slip, decreasing the threat of snapping the bit. Set the torque setting low & increase the setting if the chuck tends to slip during drilling.

Apply light pressure, just adequate for the swarf to start spiraling away from the workpiece.

Attempt to hold the drill steady. If you move it to a side rather than keeping it perpendicular while drilling, this can flex and over tension the bit, breaking it.

When drilling metal, take it simply as you break through to the other side. The bit may snag as it breaks through & captures the product at the bottom of the hole. Preferably put a block of wood under the workpiece to prevent the metal from pushing outwards as it thins before breakthrough (It is easier to do if you’re using a drill press). With experience, you learn more about the modification in noise and feel the resistance and response of the bit. As this is about to happen, so reduce off on the pressure. If bits are sharp, a considerable amount of pressure isn’t needed to drill a hole. Breakage frequently occurs when you try to lean heavily on a blunt bit to make it drill quicker, which does not work. It just gets too hot and burns it out!

Demagnetizing Drill Bits

In time, drill bits can end up getting allured, so they collect shavings while you’re drilling. That can interfere with the drilling process by increasing friction, clogging the flutes, and obstructing the cutting edge so that it can’t shave through a hole properly. A demagnetizing tool is a beneficial device for eliminating magnetism from drill bits, screwdrivers, and other tools. Typically you can likewise utilize these demagnetizing tools for alluring. That is useful, for example, for magnetizing the suggestion of a screwdriver. The request then holds the screw when you need to drive it in an unattainable area where you can’t fit your fingers.

Drill Bit Won’t Work?

Apart from the drill bit not being sharp, a typical mistake by newbies is to set their drill on the reverse so that the bit turns the wrong method. A bit ought to rotate clockwise when looking from the chuck towards the idea of the bit.

How to Sharpen Drill Bits

You can learn to hone a drill bit on the excellent grit wheel of a bench mill with some ability.

An option is to use a honing tool like this one by Drill Doctor. These makers are composed of a motor driving a tiny grindstone. To hone a drill, you place it in the proper-sized hole in the top of the sharpening tool and twist it a couple of times. This item covers all sizes up to 12 mm or 1/2 inches.

Can I Utilize “Normal” Drill Bits With an SDS Drill?

Not straight, but you can fit a basic keyed or keyless chuck. These have an SDS adapter for fitting into the SDS chuck of the drill. That allows non-SDS standard round shank drill bits to get utilized. (or hex shank, flat wood bits). Remember that you typically can’t use these chucks with a hammer action for drilling masonry.

What Is a Pillar Drill Used For?

Pillar drills (likewise called bench drills, pedestal drills, or drill presses) prevail device tools in a workshop or commercial setting. They include a base that rests on a flooring or bench, a connected column, an adjustable table that can move up & down the column (generally with a vice attached), a drill head that drives a spindle & a chuck. A motor inside the drill head runs the spindle using a sheave or equipment plan. A lever with three or four handles moves the spindle and chuck vertically. A pair of pulley blocks with stepped diameters inside the drill head are connected utilizing a v-belt. By adjusting the belt’s position on the two pulley blocks, you can vary the rotational speed of the spindle. This gear ratio control enables high-speed, low torque to get selected for little-sized drill bits and vice versa for more significant size bits.

Because it is more portable and you can find it on a workbench, the bench-drill version of the pillar-drill is ideal for DIYers.

Pillar drills have many benefits:

Holes can get drilled perpendicular to a workpiece without the bit going off course at an angle.

The spindle is moved down by a lever using a rack and pinion system. The mechanical benefit makes it much easier to press the bit into the workpiece than would hold with a traditional corded or cordless power drill.

The vice makes it possible for the workpiece to be safe, so it does not spin if the bit sticks.

You can run significant size drill bits at low speed, higher torque by varying belt positions. (Lowering the rate on a traditional power drill reduces power).

Questions & Answers

-Concern: Which type of drill bit do I require for metals such as nickel and zinc?


You can use HSS bits. However, drill bits are available with a partially ground suggestion for drilling softer nickel, zinc, and aluminum products.

-Concern: What type of drill bits can you use for metals like copper, especially copper cathode plates?


You can utilize an HSS bit or preferably a cobalt split point bit. Use kerosene as a lube, drill slowly and advance slowly and retract the bit at routine periods to help swarf removal. Copper, since its soft, binding nature, can clog the flutes in a bit, so it’s crucial not to let this occur. It likewise has a high coefficient of expansion which can intensify binding.

-Question: What type of diamond bit do I require to use for a broken head metal anchor?


If this is a drywall anchor & you wish to eliminate it, it may be simpler to push it into the wall if there’s a cavity behind it. Drive in a screw & tap it to push it in reverse.

-Concern: Which kind of drill should I utilize for drilling in a needle bore diameter is o. 46 to 0.84.?


If the holes are tiny and the product is tough, e.g., stainless steel, you might attempt utilizing carbide drill bits. These get readily offered from electronics suppliers and are for pass-through drilling holes in PCBs made from glass-reinforced epoxy. Cobalt bits are also readily available from these providers with sizes of 0.15 mm.

-Concern: Why would you say the TiN coating is defeated when honing a twist drill bit? These bits get honed by removing the product from the relief, which does not require the layer to aid the cut, only the lifting face.


The TiN finish surface area hardens the drill bit and helps to avoid friction from wearing the core and flutes. Nevertheless, if the cutting edge sharpens, the coating is gotten rid of in that region. That’s likely to degrade efficiency at the suggestion and trigger more quick wear.

-Question: Which drilling tool is most acceptable for drilling in forgings material with a radial drill maker?


Twist drill bits are most likely to be HSS, but they may be Morse taper so that they can press directly into the drill spindle.

Read More Related Article:

  1. Best Cordless Drill Set Buying Guide For 2021
  2. 4 Best Cordless Drills | 2021 Reviews
  3. What Is SDS Rotary Hammer Drill? Choose The Best One
  4. 4 Best Drill Machine Reviews | A Proper Buying Guide
  5. 3 Best Cordless Impact Drivers Reviews